Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2282 | Manualshive

Страница: 2282 / 2589

background image

1. Disconnect the lumbar support motor connector.
2. Connect battery positive voltage to lumbar support motor terminal A or B, then verify that the lumbar

support motor operate as shown in the table.

z

If the lumbar support motor does not operate as indicated in the table, replace the Seat back frame.

MOTOR OPERATION

Fig. 21: Lumbar Support Motor - Circuit Diagram

Courtesy of MAZDA MOTORS CORP.

POWER SEAT SWITCH INSPECTION

1. Disconnect the power seat switch connector.
2. Inspect for continuity between the power seat switch connector terminals.

z

If not as specified, replace the power seat switch.

Motor operation

Connection

B+ GND

Forward

B

A

Backward

A

B

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Seats - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:40:01 AM

Page 15

© 2005 Mitchell Repair Information Company, LLC.

«
...
2280
2281
2282
2283
2284
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: RAM Commercial Страницы: 12

Бренд: Mazda Страницы: 720

MCL-7000 Series

Бренд: Dakota Digital Страницы: 2

Бренд: Volvo Страницы: 284

Бренд: Yakima Страницы: 9

Бренд: PEUGEOT Страницы: 17

THERAPEDIC 2000

Бренд: Columbia Страницы: 14

XC70 - ANNEXE 808

Бренд: Volvo Страницы: 8

Бренд: Menabo Страницы: 4

Бренд: Cadillac Страницы: 538

Бренд: Mitsubishi Страницы: 284

Бренд: iDataLink Страницы: 11

Бренд: Fass Страницы: 20

Бренд: HUSKY LINERS Страницы: 3

Бренд: Myenergi Страницы: 36

Бренд: Kia Страницы: 13

Бренд: Husqvarna Страницы: 84

Бренд: Husqvarna Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды