Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 301

Страница: 301 / 2589

Fig. 252: Inspecting C3 Clutch Component

Courtesy of MAZDA MOTORS CORP.

47. Install the B1 brake band to the transaxle case.

Fig. 253: Identifying B1 Brake Band Of Transaxle Case

Courtesy of MAZDA MOTORS CORP.

48. Install the brake band anchor bolt to the transaxle case.

Tightening torque 133.3 - 199.9 N.m {13.6 - 20.3 kgf.m, 98.3 - 147.4 ft.lbf}

Fig. 254: Identifying Brake Band Anchor Bolt

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:17 AM

Page 138

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды