Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2148

Страница: 2148 / 2589

DIAGNOSTIC PROCEDURE

DTC B267C - DIAGNOSTIC PROCEDURE

STEP

INSPECTION

ACTION

INSPECT WIRING HARNESS
BETWEEN PLG CONTROL UNIT AND

LIFTGATE LATCH AND LOCK
ACTUATOR

Disconnect the PLG control module
connector.

Disconnect the liftgate latch and lock

actuator connector.

Inspect the wiring harness between
PLG control module terminal 3E and

liftgate latch and lock actuator terminal
E for an open circuit.

Yes Go to the next step.

Repair or replace the wiring harness.

Go to Step 3.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES On-Board Diagnostic (Power Liftgate (PLG) System) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:46:08 AM

Page 27

«
...
2146
2147
2148
2149
2150
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды