Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1982

Страница: 1982 / 2589

Fig. 17: Identifying Front Door Key Cylinder

Courtesy of MAZDA MOTORS CORP.

FRONT DOOR KEY CYLINDER SWITCH INSPECTION

1. Inspect for continuity between the front door key cylinder switch terminals.

If not as specified, replace the front door latch and lock actuator.

Fig. 18: Terminals Continuity Chart

Courtesy of MAZDA MOTORS CORP.

Fig. 19: Checking Continuity Between Front Door Key Cylinder Switch Terminals

Courtesy of MAZDA MOTORS CORP.

FRONT DOOR LATCH AND LOCK ACTUATOR REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the following parts:

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Security and Locks - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:58 AM

Page 12

«
...
1980
1981
1982
1983
1984
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды