Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 712

Страница: 712 / 2589

2. Connect the M-MDS to the DLC-2.
3. After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

When using the IDS (laptop PC)

1. Select "DataLogger".
2. Select "Modules".
3. Select "ABS".

When using the PDS (Pocket PC)

1. Select "Module Tests".
2. Select "ABS".
3. Select "DataLogger".

Fig. 18: Connecting M-MDS To DLC-2

Courtesy of MAZDA MOTORS CORP.

4. Select the following PIDs using the M-MDS:

WSPD_LF

(LF ABS wheel-speed sensor)

WSPD_RF

(RF ABS wheel-speed sensor)

5. Start the engine and drive the vehicle.
6. Verify that the display of the M-MDS shows the same value as the speedometer.

If there is any malfunction, replace the front ABS wheel-speed sensor.

REAR ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION [2WD]

1. Remove the trunk box. (See

TRUNK BOX REMOVAL/INSTALLATION

2. Remove the seat side box. (See

SEAT SIDE BOX REMOVAL/INSTALLATION

3. Remove the third-row seat. (See

THIRD-ROW SEAT REMOVAL/INSTALLATION

2008 Mazda CX-9 Grand Touring

2008 BRAKES Dynamic Stability Control/Roll Stability Control - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:40:24 AM

Page 19

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды