Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1552

Страница: 1552 / 2589

Fig. 7: Identifying Rear Beltline Molding With Clips And Tab

Courtesy of MAZDA MOTORS CORP.

INSTALLATION

1. Install the clip A.
2. Install the tabs B.
3. Install the clip C.
4. Install the rear beltline molding.

Fig. 8: Identifying Rear Beltline Molding With Clips And Tab

Courtesy of MAZDA MOTORS CORP.

ROOF MOLDING REMOVAL

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Exterior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:44:03 AM

Page 7

«
...
1550
1551
1552
1553
1554
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды