Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 126

Страница: 126 / 2589

Fig. 45: Connecting SST (Deployment Tool) To SST (Adapter Harness)

Courtesy of MAZDA MOTORS CORP.

8. Press the activation switch on the

SST (Deployment tool)

to operate (deploy) the pre-tensioner seat belt.

9. Disconnect the

SSTs (Deployment tool)

from the

SSTs (Adapter harness)

Fig. 46: Identifying Activation Switch

Courtesy of MAZDA MOTORS CORP.

DEPLOYMENT PROCEDURE FOR OUTSIDE OF VEHICLE

1. Inspect the

SST (Deployment tool)

(See

INSPECTION OF SST (DEPLOYMENT TOOL

).)

2. Turn the ignition switch to the LOCK position.
3. Disconnect the negative battery cable and wait for

1 min or more

4. Follow the procedure below for operating (deploying) the applicable air bag module or pre-tensioner seat

belt.

DRIVER-SIDE AIR BAG MODULE

WARNING:

The driver-side air bag module is a dual inflator type. If one inflator

is forced to operate (deploy), the other may operate (deploy)

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS Air Bag System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:16:38 AM

Page 34

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды