AMP Research 75135-01A Скачать руководство пользователя

Страница: 1 / 12

www.amp-research.com

1/10

IM75135 rev 07.30.19

I N S T A L L A T I O N G U I D E

3-5 Hours

Professional installation recommended

Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one of the following patents:

Printed in USA.

TOOLS REQUIRED

Safety goggles

Measuring tape

10 mm socket

13 mm socket

1/2” socket

Ratchet wrench and extension

Wire crimpers

Wire stripper / cutter

3/16” hex key wrench (allen wrench)

4mm hex key wrench ( allen wrench )

Electrical tape

Weather proof caulking (silicone sealer)

Silicone spray

INSTALLATION TIME

1 2 3

SKILL LEVEL

4= Experienced

AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2) Monday - Friday, 7:00 AM - 5:00 PM PST

APPLICATION

AMP

Part

Jeep Wrangler JT

2020

75135-01A

5-Year Limited Warranty

WARRANTY

Содержание 75135-01A













Результаты поиска

Содержание 75135-01A

Отзывы:

Похожие инструкции для 75135-01A

Бренды по названию

Популярные бренды

AMP Research 75135-01A, Руководство по установке

Результаты поиска

Содержание 75135-01A

Отзывы:

Похожие инструкции для 75135-01A

Бренды по названию

Популярные бренды