Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1993

Страница: 1993 / 2589

Closer motor

1. Apply battery positive voltage and connect ground to the corresponding closer motor terminals, and

inspect the closer motor operation.

Fig. 41: Applying Battery Positive Voltage & Connect Ground To Corresponding Closer Motor

Terminals

Courtesy of MAZDA MOTORS CORP.

If not as indicated in the table, replace the liftgate latch and lock actuator.

LIFTGATE LATCH AND LOCK ACTUATOR REFERENCE

Fig. 42: Identifying Closer Motor Reverse & Normal Rotation

Courtesy of MAZDA MOTORS CORP.

VEHICLES WITHOUT PLG

Liftgate latch switch

1. When inspecting the latch, press the latch lever using a flathead screwdriver or a similar tool.

Operation

Terminal

Normal rotation GND B+

Reverse rotation B+ GND

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Security and Locks - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:58 AM

Page 23

«
...
1991
1992
1993
1994
1995
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды