Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 352

Страница: 352 / 2589

Fig. 22: Identifying Coupler Component Connector Terminal

Courtesy of MAZDA MOTORS CORP.

OFF-VEHICLE INSPECTION

1. Disconnect the negative battery cable.
2. Remove the air cleaner component. (See

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION

[MZI-3.7]

3. Drain the ATF. (See

AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT [AW6A-EL,

AW6AX-EL]

4. Remove the oil cooler.
5. Remove the oil pipe. (See

OIL COOLER REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

6. Remove the control valve body. (See

CONTROL VALVE BODY REMOVAL/INSTALLATION

[AW6A-EL, AW6AX-EL]

7. Remove the input/turbine speed sensor. (See

INPUT/TURBINE SPEED SENSOR

REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

WARNING:

A hot transaxle and ATF can cause severe burns. Turn off the engine

and wait until they are cool before replacing the ATF.

CAUTION:

Water or foreign material entering the connector can cause a poor
connection or corrosion. Be sure not to allow water or foreign

material on the connector when disconnecting.

Do not damage the terminals.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:30 AM

Page 24

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды