Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 173

Страница: 173 / 2589

10. Using a plastic hammer, tap the control valve body cover to remove it.

1. Insert a precision screwdriver from the backside into the connector as shown in the figure.

Fig. 12: Identifying Control Valve Body Cover Bolts

Courtesy of MAZDA MOTORS CORP.

CAUTION:

Be careful not to damage the solenoid valves and connectors.

Do not pull the wiring harnesses when removing the connector.

NOTE:

Disconnect the solenoid connector according to the following

procedure:

Fig. 13: Tapping Control Valve Body Cover

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:15 AM

Page 10

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды