Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 193

Страница: 193 / 2589

Fig. 57: Identifying O-Rings Of Oil Cooler Outlet Tube

Courtesy of MAZDA MOTORS CORP.

58. Using a flathead screwdriver and a hammer, pry back the crimp on the lockwashers.

59. Remove the lockwashers, washers and the counter drive gear.

CAUTION:

If the lockwasher crimp is not completely pried back, the tool

cannot fit over the bolt properly and the bolt cannot be
loosened.

Fig. 58: Prying Back Crimp On Lockwashers
Courtesy of MAZDA MOTORS CORP.

CAUTION:

Do not damage the VSS wiring harness.

2008 Mazda CX-9 Grand Touring

2005-08 TRANSMISSION Automatic Transaxle Overhaul (AW6A-EL) - CX-7, CX-9 & Mazda 6

Microsoft

Sunday, November 15, 2009 10:28:16 AM

Page 30

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды