Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1744

Страница: 1744 / 2589

NO.1 INSUFFICIENT AIR (OR NO AIR) BLOWN FROM FRONT VENTS

NO.1 INSUFFICIENT AIR (OR NO AIR) BLOWN FROM FRONT VENTS DESCRIPTION AND

POSSIBLE CAUSE

REC/FRESH mode.

No temperature control with front

climate control unit

Malfunction in A/C unit and/or front climate control unit
air mix system

Temperature does not change when switching front

climate control unit temperature setting dial.

5 Windshield fogged

Malfunction in A/C compressor control system and/or air

intake mode switching system

A/C compressor does not operate while airflow mode is
DEFROSTER or HEAT/DEF modes.

Air intake mode does not change to FRESH while airflow
mode is in DEFROSTER or HEAT/DEF modes.

Insufficient air (or no air) from rear
vent

Problem with each rear vent and/or duct

Rear airflow mode does not change when front and/or
rear climate control unit mode switches.

7 Amount of air from rear vent does

not change

Malfunction in rear blower motor system

Amount of air blowing rear vents does not change when

switching front and/or rear climate control unit airflow
volume control dial.

Air from front/rear vents not cold
enough

Malfunction in A/C basic system

Magnetic clutch operates but A/C system malfunctions.

9 No cool air from front/rear vents

Malfunction in A/C compressor control system

Magnetic clutch does not operate when the A/C system is

turned ON.

10 Noise while operating A/C system

Problem with A/C basic system installation

Noise from magnetic clutch, A/C compressor, hose or
refrigerant line.

11 Dual A/C control function does not

operate

Malfunction in A/C unit and/or front climate control unit
dual A/C control system

Driver or passenger-side temperature control dial does not

operate individually.

Insufficient air (or no air) blown from front vents

DESCRIPTION

Problem with each vent and/or duct

Front airflow mode does not change when switching front mode switch.

Malfunction in front airflow mode actuator

2008 Mazda CX-9 Grand Touring

2008 HVAC Symptom Troubleshooting (HVAC) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:14:50 AM

Page 3

«
...
1742
1743
1744
1745
1746
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды