Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2405

Страница: 2405 / 2589

Fig. 33: Identifying Dam Cut Point

Courtesy of MAZDA MOTORS CORP.

5. Align the marks made before removal and install the pin to the windshield referring to the figure, (when

reusing the glass, and the pin was removed)

6. Install the windshield molding.

Fig. 34: Identifying Hollowed Mark In Ceramic Coating

Courtesy of MAZDA MOTORS CORP.

7. Use glass primer on the glass, then allow it to dry for

approx. 30 min.

CAUTION:

To prevent weakening of the primer adhesion, keep the bonding

surface free of dirt, moisture, and grease. Do not touch the

surface with your hand.

NOTE:

Make sure to apply primer to the hollowed marks in the ceramic coating.

Fig. 35: Identifying Primer Applying Area

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Glass/Windows/Mirrors - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:36:16 AM

Page 26

«
...
2403
2404
2405
2406
2407
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды