Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2175

Страница: 2175 / 2589

Fig. 15: Identifying Steering Gear, Linkage Components & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

STEERING GEAR AND LINKAGE INSTALLATION NOTE

1. Tighten the mounting bracket bolts to the specified torque in the order shown.

Tightening torque 96.9-136.0 N.m {9.89-13.86 kgf.m, 71.5-100.3 ft.lbf}

Fig. 16: Identifying Mounting Bracket Bolts Tightening Order

Courtesy of MAZDA MOTORS CORP.

BOLT (INTERMEDIATE SHAFT) INSTALLATION NOTE

1. Align the marks and install the intermediate shaft and bolt.

STEERING GEAR AND LINKAGE DISASSEMBLY

2008 Mazda CX-9 Grand Touring

2008 STEERING Power Steering - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:20:34 AM

Page 12

«
...
2173
2174
2175
2176
2177
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды