Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 450

Страница: 450 / 2589

Fig. 14: Identifying Front Over Fender Lower And Front Bumper Fascia With Nuts

Courtesy of MAZDA MOTORS CORP.

FRONT BUMPER REINFORCEMENT REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the front bumper. (See

FRONT BUMPER REMOVAL/INSTALLATION

3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.

Fig. 15: Identifying Removing Sequence Of Front Bumper Reinforcement Components & Torque

Specifications

Courtesy of MAZDA MOTORS CORP.

REAR BUMPER REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the rear combination light. (See

REAR COMBINATION LIGHT

REMOVAL/INSTALLATION

3. Remove the screw and fastener.
4. Detach the tab of the splash shield to remove it.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Body Panels - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:44:45 AM

Page 11

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды