Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1879

Страница: 1879 / 2589

1. Remove the following parts:

1. Dashboard under cover (Passenger side) (See

DASHBOARD UNDER COVER

REMOVAL/INSTALLATION

2. Glove compartment service hole cover (See

AIR FILTER REMOVAL/INSTALLATION

2. Pull the stay damper in the direction shown in the figure, and detach the connecting part between the

glove compartment and the stay damper.

Fig. 18: Identifying Glove Compartment & Stay Damper

Courtesy of MAZDA MOTORS CORP.

3. Insert fingers into the glove compartment service hole and detach the stoppers while holding the

instrument panel.

Fig. 19: Identifying Glove Compartment Service Hole

Courtesy of MAZDA MOTORS CORP.

4. Lower the glove compartment.
5. Detach the hook from the dashboard and remove the glove compartment.
6. Install in the reverse order of removal.

damper, the stay damper may be damaged. Verify that the stay

damper is joined to the glove compartment before closing the glove
compartment.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 15

«
...
1877
1878
1879
1880
1881
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды