Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2116

Страница: 2116 / 2589

BRAKE CALIPER COMPONENT REMOVAL NOTE

1. Remove the brake caliper assembly from the trailing link and suspend it with a cable so it does not

interfere.

Fig. 16: Identifying Brake Caliper Component

Courtesy of MAZDA MOTORS CORP.

DISC PLATE REMOVAL NOTE

1. If any disc plate is difficult to remove, perform the following steps to remove it.

1. Insert a flathead screwdriver into the service hole and turn the adjuster in the direction of the arrow

to compress the parking brake shoe.

2. Remove the disc plate.

Fig. 17: Adjusting Disc Plate Adjuster

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 BRAKES Parking Brake System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:48:01 AM

Page 13

«
...
2114
2115
2116
2117
2118
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды