manualshive.com logo in svg

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Mazda CX-9 Grand Touring 2008 - роскошный семиместный кроссовер с высоким уровнем комфорта и мощным двигателем. Перед вами отличная возможность скачать бесплатно руководство пользователя для этой модели на manualshive.com. Получите свой экземпляр уже сегодня и ознакомьтесь с функциональностью автомобиля.

Поделиться
Скачать
background image

2. Connect a 

1.5 V

 battery to the center speaker and verify that noise is heard from the center speaker. 

z

If no noise is heard, replace the center speaker. 

Fig. 21: Identifying Center Speaker Terminals

 

Courtesy of MAZDA MOTORS CORP.

 

REAR SPEAKER REMOVAL/INSTALLATION 

1. Disconnect the negative battery cable.  
2. Remove the following parts: 

1. Trunk box (See 

TRUNK BOX REMOVAL/INSTALLATION

 .)  

2. Seat side box (See 

SEAT SIDE BOX REMOVAL/INSTALLATION

 .)  

3. Trunk end trim (See 

TRUNK END TRIM REMOVAL/INSTALLATION

 .)  

4. Third-row seat (See 

THIRD-ROW SEAT REMOVAL/INSTALLATION

 .)  

5. Third-row seat belt lower anchor installation bolt (See 

THIRD-ROW SEAT BELT 

REMOVAL/INSTALLATION

 .)  

6. Rear scuff plate inner (See 

REAR SCUFF PLATE REMOVAL/INSTALLATION

 .)  

7. Trunk side trim (See 

TRUNK SIDE TRIM REMOVAL/INSTALLATION

 .)  

8. Roof side trim (See 

ROOF SIDE TRIM REMOVAL/INSTALLATION

 .)  

9. Third-row seat belt upper anchor installation bolt (See 

THIRD-ROW SEAT BELT 

REMOVAL/INSTALLATION

 .)  

10. D-pillar trim (See 

D-PILLAR TRIM REMOVAL/INSTALLATION

 .)  

3. Remove in the order indicated in the table. 

Fig. 22: Identifying Rear Speaker Components

 

2008 Mazda CX-9 Grand Touring 

2008 BODY & ACCESSORIES Entertainment - Mazda CX-9

  

Microsoft 

 

Sunday, November 15, 2009 10:47:06 AM

Page 15 

© 2005 Mitchell Repair Information Company, LLC. 

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Bimmer Jakes FRONT HEADLIGHT LENS COVER Replacement Manual preview
FRONT HEADLIGHT LENS COVER
Бренд: Bimmer Jakes Страницы: 4
Metra Electronics 95-6556 Installation Instructions preview
95-6556
Бренд: Metra Electronics Страницы: 4
Rostra REARSIGHT OnStar 250-8822 Installation Instructions preview
REARSIGHT OnStar 250-8822
Бренд: Rostra Страницы: 2
Yakima Whispbar K887W Fitting Instructions Manual preview
Whispbar K887W
Бренд: Yakima Страницы: 19
Nav TV UCI-11C NTV-KIT331 User Manual preview
UCI-11C NTV-KIT331
Бренд: Nav TV Страницы: 4
Mazda 2 2016 Owner'S Manual preview
2 2016
Бренд: Mazda Страницы: 720
GMC Chevrolet Silverado 2500HD 2021 Owner'S Manual preview
Chevrolet Silverado 2500HD 2021
Бренд: GMC Страницы: 433
Jeep GLADIATOR 2022 Owner'S Manual preview
GLADIATOR 2022
Бренд: Jeep Страницы: 380
Buick Electra 225 1965 Service Manual preview
Electra 225 1965
Бренд: Buick Страницы: 914
SNIPER V2 Inox Owner'S Manual preview
V2 Inox
Бренд: SNIPER Страницы: 2
Calix group TYP MVP 823 Assembly Instructions preview
TYP MVP 823
Бренд: Calix group Страницы: 4
Jeep Grand Cherokee SRT 2019 Owner'S Manual preview
Grand Cherokee SRT 2019
Бренд: Jeep Страницы: 656
Westin 32-1660 Instructions preview
32-1660
Бренд: Westin Страницы: 3
Spracht Aura Mobile BT MCP-2014 Quick Start Manual preview
Aura Mobile BT MCP-2014
Бренд: Spracht Страницы: 2
JBA 1674S Installation Instructions preview
1674S
Бренд: JBA Страницы: 5
Laser PW-BT50AR Quick Start Manual preview
PW-BT50AR
Бренд: Laser Страницы: 3
Pinnacle EPL7SAM+C Series Quick Start Manual preview
EPL7SAM+C Series
Бренд: Pinnacle Страницы: 2
ACV 381178-12 Installation Manual preview
381178-12
Бренд: ACV Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды