Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 117

Страница: 117 / 2589

AIR BAG MODULE AND PRE-TENSIONER SEAT BELT DEPLOYMENT
PROCEDURES

Fig. 30: Continuity Chart
Courtesy of MAZDA MOTORS CORP.

Fig. 31: Identifying Vehicle-Side Connector And Air Bag Module-Side

Connector Terminals
Courtesy of MAZDA MOTORS CORP.

WARNING:

A live (undeployed) air bag module or pre-tensioner seat belt may

accidentally operate (deploy) when it is disposed of and cause

serious injury. Do not dispose of a live (undeployed) air bag module
and pre-tensioner seat belt. If the SSTs (Deployment tool and

Adapter harness) are not available, consult the nearest Mazda

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS Air Bag System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:16:38 AM

Page 25

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды