Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 839

Страница: 839 / 2589

If voltage is not as following table, perform the "Circuit Open/Short Inspection".

If there is no open or short circuit, replace accelerator pedal. (See

ACCELERATOR

PEDAL REMOVAL/INSTALLATION [MZI-3.7]

APP sensor output voltage

APP SENSOR OUTPUT VOLTAGE SPECIFICATION CHART

CIRCUIT OPEN/SHORT INSPECTION

Fig. 19: Identifying Accelerator Pedal Position Sensor & PCM Wiring Harness Side Connector

Courtesy of MAZDA MOTORS CORP.

1. Disconnect the PCM connector. (See

PCM REMOVAL/INSTALLATION [MZI-3.7]

2. Inspect the following wiring harnesses for open or short circuit. (Continuity inspection)

Condition

PCM terminal 1AK (APP

sensor No.1)

PCM terminal 1AG (APP

sensor No.2)

PCM terminal 1 AC

(APP sensor No.3)

Accelerator pedal
released

Approx. 4.1 V

Approx. 1.5 V

Approx. 0.1 V

Accelerator pedal

depressed

Approx. 1.0 V

Approx. 3.9 V

Approx. 3.3 V

2008 Mazda CX-9 Grand Touring

2008 ENGINE Control System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:07:19 AM

Page 21

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды