Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2159

Страница: 2159 / 2589

DIAGNOSTIC PROCEDURE

DTC B2936 - DIAGNOSTIC PROCEDURE

DTC B2937 [POWER LIFTGATE (PLG) SYSTEM]

DTC B2937 - DETECTION CONDITION POSSIBLE CAUSE CHART

STEP

INSPECTION

ACTION

INSPECT WIRING HARNESS
BETWEEN PLG CONTROL MODULE

AND PLG DRIVE UNIT

Disconnect the PLG control module

connector.

Disconnect the PLG drive unit
connector.

Inspect PLG control module

terminals 1E and 1F, and PLG drive
unit terminals A and B for an open

circuit.

Is the wiring harness normal?

Yes

Replace the PLG drive unit.
(See

POWER LIFTGATE (PLG) DRIVE

UNIT REMOVAL/INSTALLATION

Go to the next step.

Repair or replace the wiring harness.

Go to the next step.

VERIFY CORRECTION

COMPLETED

Reconnect the disconnected
connector.

Clear the DTC.

Operate the PLG system.

Is DTC B2936 stored?

Yes

Replace the PLG control module.

(See

POWER LIFTGATE (PLG) CONTROL

MODULE REMOVAL/INSTALLATION

DTC troubleshooting completed.

DTC B2937

PLG motor circuit malfunction

DETECTION

CONDITION

PLG motor current is excessively low. (less than 1A)

POSSIBLE CAUSE

Open circuit in wiring harness between PLG control module terminal 1E and

PLG motor terminal A (PLG drive unit)

Open circuit in wiring harness between PLG control module terminal 1F and
PLG motor terminal B (PLG drive unit)

PLG motor malfunction

PLG control module malfunction

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES On-Board Diagnostic (Power Liftgate (PLG) System) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:46:08 AM

Page 38

«
...
2157
2158
2159
2160
2161
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды