Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 439 | Manualshive

Страница: 439 / 2589

background image

18. Turn the ignition switch to ON position.
19. Install the interlock cable to the steering lock.
20. Slide the outer casing to the steering lock and insert the clip over the convex part of the outer casing.

Fig. 40: Identifying Clip And Convex Part

Courtesy of MAZDA MOTORS CORP.

switch with a new one when replacing the power brake unit or

the pedal, or performing any procedure that changes the pedal
stroke.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle Shift Mechanism - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:30:13 AM

Page 19

© 2005 Mitchell Repair Information Company, LLC.

«
...
437
438
439
440
441
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Federal Signal Corporation Страницы: 13

Бренд: LAMBORGHINI Страницы: 48

Бренд: Axxess Страницы: 4

Бренд: Vintage Air Страницы: 14

Бренд: Trailboss Страницы: 5

WirelessAIR 73000EZ

Бренд: Air Lift Страницы: 12

Бренд: Thule Страницы: 8

Бренд: RAM Страницы: 76

Бренд: Advantech Страницы: 59

Бренд: Fab Fours Страницы: 19

Бренд: Webasto Страницы: 18

RGBW Rock Lights

Бренд: Lit Lightz Страницы: 3

Бренд: NanoCam Plus Страницы: 32

A-18 TRAILER ABS

Бренд: BENDIX Страницы: 40

Бренд: Toyota Страницы: 56

Бренд: Mopar Страницы: 18

Бренд: Axxess Страницы: 8

Бренд: Reliant Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды