Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1904 | Manualshive

Страница: 1904 / 2589

background image

Fig. 62: Identifying Trunk Side Trim Components (Passenger Side)

Courtesy of MAZDA MOTORS CORP.

FRONT DOOR TRIM REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the inner garnish. (See

INNER GARNISH REMOVAL/INSTALLATION

.)

3. Open the cover using a small flathead screwdriver and remove the screw.
4. Remove the armrest garnish in the direction of the arrow.
5. Remove the bolt.
6. Detach clips A from the front door using a fastener remover.
7. Pull the front door trim upward and detach tabs B from the front door.

Fig. 63: Identifying Armrest Garnish, Clips & Bolts

Courtesy of MAZDA MOTORS CORP.

8. Remove tab A, and move the front door trim in the direction of the arrow.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 40

© 2005 Mitchell Repair Information Company, LLC.

«
...
1902
1903
1904
1905
1906
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Roav Страницы: 10

PICASSO XSARA DESIRE 1.6 - MESUREMENT

Бренд: CITROEN Страницы: 2

For 1985-1992 GM Cars and Trucks 17933

Бренд: Edelbrock Страницы: 4

Gasoline/Electric DS Golf Car 1996

Бренд: Club Car Страницы: 48

Бренд: femkes Страницы: 7

Бренд: Rati Страницы: 2

Бренд: BMW Страницы: 38

Бренд: Hudson Страницы: 34

Бренд: Sanitas Страницы: 36

Бренд: JKS Страницы: 6

Бренд: BrandMotion Страницы: 6

Бренд: INDIWORK Страницы: 18

Бренд: Opel Страницы: 103

Бренд: Skoda Страницы: 2

Бренд: FORM FIT Страницы: 2

Бренд: Mobileye Страницы: 29

Бренд: Buick Страницы: 161

Бренд: Brink Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды