Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 825

Страница: 825 / 2589

Fig. 6: Identifying PCM Bracket, Connector & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

PCM INSPECTION [MZI-3.7]

PCM INSPECTION PREPARATION

1. Disconnect the negative battery cable.
2. Remove the battery and battery tray. (See

BATTERY REMOVAL/INSTALLATION [MZI-3.7]

3. Remove the windshield wiper arm and blade. (See

WINDSHIELD WIPER ARM AND BLADE

REMOVAL/INSTALLATION

4. Remove the cowl grille. (See

COWL GRILLE REMOVAL/INSTALLATION

5. Remove the windshield wiper motor. (See

WINDSHIELD WASHER MOTOR

REMOVAL/INSTALLATION

6. Remove the cowl panel. (See

COWL PANEL REMOVAL/INSTALLATION

7. Remove the PCM connector still connected.
8. Install the battery and battery tray. (See

BATTERY REMOVAL/INSTALLATION [MZI-3.7]

9. Connect the negative battery cable.

TYPICAL DIAGNOSTIC REFERENCE VALUES

CAUTION:

The PCM terminal voltage can vary with the conditions when
measuring and changes due to aged deterioration on the vehicle,

causing false diagnosis. Therefore determine comprehensively where
the malfunction occurs among the input systems, output systems,

and the PCM.

2008 Mazda CX-9 Grand Touring

2008 ENGINE Control System (MZI-3.7) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:07:19 AM

Page 7

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды