Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2178

Страница: 2178 / 2589

1. Place alignment marks as shown in the figure for proper installation.

Fig. 18: Identifying Tie-rod End Alignment Marks

Courtesy of MAZDA MOTORS CORP.

LOCK WASHER, TIE ROD DISASSEMBLY NOTE

1. Unclamp the washer.
2. Lock the steering rack end against rotation with a wrench and remove the tie rod.
3. Remove the lock washer.

Fig. 19: Removing Tie Rod

Courtesy of MAZDA MOTORS CORP.

HOLDER, OIL SEAL (HOLDER SIDE) DISASSEMBLY NOTE

1. Remove the holder from the gear housing using the

SST.

2008 Mazda CX-9 Grand Touring

2008 STEERING Power Steering - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:20:34 AM

Page 15

«
...
2176
2177
2178
2179
2180
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды