Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1895

Страница: 1895 / 2589

REMOVAL/INSTALLATION

4. B-pillar lower trim (See

B-PILLAR LOWER TRIM REMOVAL/INSTALLATION

5. Front seat belt upper anchor installation bolt (See

FRONT SEAT BELT

REMOVAL/INSTALLATION

2. Partially peel back the seaming welt.
3. Detach clips A and C, and pin B by pulling them in the direction of the arrow.

Fig. 47: Identifying B-Pillar Upper Trim With Pin & Clips

Courtesy of MAZDA MOTORS CORP.

4. Remove the B pillar upper trim in the direction of the arrow.
5. Install in the reverse order of removal.

Fig. 48: Identifying B-Pillar Upper Trim

Courtesy of MAZDA MOTORS CORP.

ROOF SIDE TRIM REMOVAL/INSTALLATION

1. Detach clip A and B, and tab C by pulling them in the direction of the arrow.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 31

«
...
1893
1894
1895
1896
1897
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды