Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2018 | Manualshive

Страница: 2018 / 2589

background image

2. Remove the console cover. (See

CONSOLE COVER REMOVAL/INSTALLATION

.)

3. Remove the clips.
4. Disconnect the connector, then remove the keyless antenna.
5. Install in the reverse order of removal.

Fig. 71: Identifying Keyless Antenna & Connector With Screw (Interior, Middle)

Courtesy of MAZDA MOTORS CORP.

INTERIOR, REAR

1. Disconnect the negative battery cable.
2. Remove the trunk box. (See

TRUNK BOX REMOVAL/INSTALLATION

.)

3. Remove the third-row seat. (See

THIRD-ROW SEAT REMOVAL/INSTALLATION

.)

4. Partially peel back the floor covering.
5. Remove the nuts.
6. Disconnect the connector, then remove the keyless antenna.
7. Install in the reverse order of removal.

Fig. 72: Identifying Keyless Antenna, Connector With Screw & Torque Specifications (Interior,

Rear)

Courtesy of MAZDA MOTORS CORP.

KEYLESS BEEPER REMOVAL/INSTALLATION [ADVANCED KEYLESS

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Security and Locks - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:58 AM

Page 48

© 2005 Mitchell Repair Information Company, LLC.

«
...
2016
2017
2018
2019
2020
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: Federal Signal Corporation Страницы: 13

Бренд: Ignition Страницы: 1

Бренд: iArmor Страницы: 6

2012 Escalade Hybrid

Бренд: Cadillac Страницы: 90

Бренд: Curt Manufacturing Страницы: 6

Бренд: ideus Страницы: 159

Бренд: Rugged Ridge Страницы: 2

Бренд: Cadillac Страницы: 19

Бренд: r.LiNK Страницы: 21

Бренд: Toyota Страницы: 672

Бренд: Cadillac Страницы: 48

Бренд: ULTIMATE SPEED Страницы: 26

Sebring Convertible

Бренд: Chrysler Страницы: 454

Full Display Mirror

Бренд: Gentex Страницы: 18

Бренд: Chevrolet Страницы: 103

Бренд: Peak Страницы: 8

Бренд: Renault Страницы: 239

Бренд: Honda Страницы: 234

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды