Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2370

Страница: 2370 / 2589

Fig. 1: Troubleshooting Chart

Courtesy of MAZDA MOTORS CORP.

NOTE:

The exterior open/close function does not operate when the following

conditions are met.

{

Any door or liftgate is open.

{

The key is inserted in the steering lock.

{

The start knob is not in the LOCK position.

The auto-open/close function (the exterior open/close function) does not
operate if the power window initialization procedure has been reset.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Symptom Troubleshooting [Power Window System (Exterior Open/Close Function)] -

Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:37:40 AM

Page 2

«
...
2368
2369
2370
2371
2372
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды