Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1536

Страница: 1536 / 2589

Fig. 62: Identifying Inverter Unit Connector Terminals

Courtesy of MAZDA MOTORS CORP.

TERMINAL VOLTAGE TABLE

VOLTAGE SPECIFICATION

REAR MOUNT CAMERA REMOVAL/INSTALLATION

1. Remove the liftgate upper trim. (See

LIFTGATE UPPER TRIM REMOVAL/INSTALLATION

2. Remove the liftgate side trim. (See

LIFTGATE SIDE TRIM REMOVAL/INSTALLATION

3. Remove the liftgate lower trim. (See

LIFTGATE LOWER TRIM REMOVAL/INSTALLATION

4. Remove the rear finisher. (See

REAR FINISHER REMOVAL/INSTALLATION

5. Remove in the order indicated in the table.

Fig. 63: Identifying Rear Mount Camera Screws

Courtesy of MAZDA MOTORS CORP.

Terminal

Signal

name

Connected to

Measured condition Voltage (V)/

Continuity

Inspection item (s)

A, B

AC power

supply

output

Power supply

socket (AC 115 V)

Ignition switch is at
ACC or ON position

AC 103-5-

126.5

Power supply
socket (AC

115V)

Related wiring
harnesses

Ignition switch is at

LOCK position

1.0 or less

ACC

MIRROR 7.5 A

fuse

Ignition switch is at
ACC or ON position

B+

MIRROR 7.5 A
fuse

Related wiring

harnesses

Ignition switch is at

LOCK position

1.0 or less

Power

supply

AC PWR 15 A

fuse

Under any condition

B+

AC PWR 15 A
fuse

Related wiring

harnesses

GND

Body ground

Under any condition

1.0 or less

Related wiring

harnesses

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Entertainment - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:47:06 AM

Page 36

«
...
1534
1535
1536
1537
1538
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды