Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2265

Страница: 2265 / 2589

3. Remove the second-row buckle (RH).
4. Install in the reverse order of removal.

Fig. 13: Identifying Second-Row Buckle (RH), Bolt & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

THIRD-ROW BUCKLE REMOVAL/INSTALLATION

REMOVAL

1. Fold the third-row seat backs forward.
2. Remove the trunk box. (See

TRUNK BOX REMOVAL/INSTALLATION

3. Remove the bolt.
4. Remove the third-row buckle.

Fig. 14: Identifying Third-Row Buckle & Bolt

Courtesy of MAZDA MOTORS CORP.

INSTALLATION

1. Bind the third-row seat belt buckles in a band as shown in the figure.

2008 Mazda CX-9 Grand Touring

2008 RESTRAINTS Seat Belt - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:19:40 AM

Page 11

«
...
2263
2264
2265
2266
2267
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды