Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2172 | Manualshive

Страница: 2172 / 2589

background image

Fig. 10: Locating Pin

Courtesy of MAZDA MOTORS CORP.

STEERING LOCK MOUNTING BOLTS INSTALLATION NOTE

1. Assemble the steering lock component to the steering shaft.
2. Verify that the lock operates correctly.
3. Install new steering lock mounting bolts.
4. Tighten the bolts until the heads break off.

Fig. 11: Installing Steering Lock Mounting Bolts

Courtesy of MAZDA MOTORS CORP.

STEERING SHAFT INSTALLATION NOTE

1. Lock the tilt lever.
2. Tighten nut A.
3. Tighten nut B.
4. Tighten bolt C.

CAUTION:

z

Do not apply a shock in the axial direction of the shaft.

2008 Mazda CX-9 Grand Touring

2008 STEERING Power Steering - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:20:34 AM

Page 9

© 2005 Mitchell Repair Information Company, LLC.

«
...
2170
2171
2172
2173
2174
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

MARTEN-FREE CAR

Бренд: Gardigo Страницы: 36

Porsche 911 GT3 R

Бренд: iRacing Страницы: 25

Бренд: rough country Страницы: 4

Fleetwood Brougham Sedan 1966

Бренд: Cadillac Страницы: 56

Бренд: Lexus Страницы: 830

Бренд: Brink Страницы: 21

Charger SRT 392 2017

Бренд: Dodge Страницы: 576

Бренд: Lexus Страницы: 108

Бренд: TATA Motors Страницы: 232

Бренд: Rhino-Rack Страницы: 2

Бренд: Whispbar Страницы: 14

Бренд: Magneti Marelli Страницы: 3

Бренд: Metra Electronics Страницы: 12

Бренд: Chipolino Страницы: 11

Бренд: Mercedes-Benz Страницы: 108

Бренд: VanEssa mobilcamping Страницы: 12

Бренд: GMC Страницы: 40

CF-UFORCE-SDK01

Бренд: FALCON RIDGE Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды