Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2447 | Manualshive

Страница: 2447 / 2589

background image

Fig. 14: Identifying Windshield Washer Hoses, Joint Pipe And Clips

Courtesy of MAZDA MOTORS CORP.

9. Remove windshield washer hose C from hook A.

10. Disconnect joint pipe B and C, than remove windshield washer hose C.
11. Disconnect joint pipe C and remove windshield washer hose D.
12. Disconnect windshield washer hose E from the windshield washer nozzle.
13. Disconnect joint pipe D and remove windshield washer hose E.
14. Remove the windshield washer hose F from the hooks B.
15. Disconnect windshield washer hose F from the windshield washer nozzle.
16. Disconnect joint pipe D and remove windshield washer hose F.
17. Install in the reverse order of removal.

Fig. 15: Identifying Windshield Washer Hoses, Hooks And Joint Pipes

Courtesy of MAZDA MOTORS CORP.

WASHER FLUID-LEVEL SENSOR REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the front bumper. (See

FRONT BUMPER REMOVAL/INSTALLATION

.)

3. Remove the washer tank. (See

WASHER TANK REMOVAL/INSTALLATION

.)

4. Remove in the order indicated in the table.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Wiper/Washer System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:35:20 AM

Page 12

© 2005 Mitchell Repair Information Company, LLC.

«
...
2445
2446
2447
2448
2449
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CX-9 Grand Touring 2008

Бренд: J-Top Страницы: 2

Бренд: RAM Commercial Страницы: 12

Бренд: Honda Страницы: 73

Бренд: Aries Страницы: 3

1973 Crown Hardtop

Бренд: Toyota Страницы: 50

Бренд: Atera Страницы: 10

4500 CHASSIS CAB 2012

Бренд: RAM Страницы: 7

Бренд: femkes Страницы: 7

Бренд: Whispbar Страницы: 15

Бренд: Sears Страницы: 41

Бренд: ULTIMATE SPEED Страницы: 50

Бренд: RAM Страницы: 496

Hatch-bag Luggage System

Бренд: Tabernus Peram Страницы: 10

CMPC-22 Fujitsu-Siemens PocketLoox 410

Бренд: Carcomm Страницы: 2

Бренд: Whispbar Страницы: 15

Бренд: Lock'er Down Страницы: 2

Бренд: Buick Страницы: 58

Бренд: PERODUA Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды