Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2448

Страница: 2448 / 2589

Fig. 16: Identifying Washer Fluid-Level Sensor Remove/Install Components

Courtesy of MAZDA MOTORS CORP.

5. Install in the reverse order of removal.

WASHER FLUID-LEVEL SENSOR INSPECTION

1. Disconnect the negative battery cable.
2. Verify that continuity between the washer fluid-level sensor terminals is as indicated in the table.

If not as specified, replace the washer fluid-level sensor.

Fig. 17: Washer Fluid-Level Sensor Terminals Continuity Chart

Courtesy of MAZDA MOTORS CORP.

Fig. 18: Identifying Washer Fluid-Level Sensor Terminals

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Wiper/Washer System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:35:20 AM

Page 13

«
...
2446
2447
2448
2449
2450
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды