Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2105

Страница: 2105 / 2589

1. Turn the ignition switch on, depress the parking brake pedal one notch, and verify that the brake

system warning light illuminates.

2. Verify that the rear brakes do not drag.

Fig. 2: Identifying Adjusting Nut

Courtesy of MAZDA MOTORS CORP.

PARKING BRAKE REMOVAL/INSTALLATION [2WD]

1. Perform the following procedure and remove the parking brake pedal.

1. Remove the dashboard under cover (LH). (See

DASHBOARD UNDER COVER

REMOVAL/INSTALLATION

2. Perform the following procedure and remove the front parking brake cable.

1. Remove the front seat (Driver side). (See

FRONT SEAT REMOVAL/INSTALLATION

2. Remove the decoration panel. (See

DECORATION PANEL REMOVAL/INSTALLATION

3. Remove the front console box mat, (See

FRONT CONSOLE BOX MAT

REMOVAL/INSTALLATION

4. Remove the indicator panel. (See

INDICATOR PANEL REMOVAL/INSTALLATION

5. Remove the front console box. (See

FRONT CONSOLE BOX REMOVAL/INSTALLATION

6. Remove the dashboard under cover (LH). (See

DASHBOARD UNDER COVER

REMOVAL/INSTALLATION

CAUTION:

Performing the following procedures without first removing the ABS
wheel-speed sensor may possibly cause an open circuit in the

harness if it is pulled by mistake. Before performing the following

procedures, remove the ABS wheel-speed sensor (axle side) and fix it
to an appropriate place where the sensor will not be pulled by

mistake while servicing the vehicle.

2008 Mazda CX-9 Grand Touring

2008 BRAKES Parking Brake System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:48:01 AM

Page 2

«
...
2103
2104
2105
2106
2107
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды