Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 2204

Страница: 2204 / 2589

TYPE A

1. Verify the continuity between the relay terminals.

If not as indicated in the table, replace the relay.

Fig. 11: Relay Terminals Continuity Chart (Type A)

Courtesy of MAZDA MOTORS CORP.

4 terminals

Type A

Starter relay

Back-up light relay

A/C relay

TNS relay

Horn relay

Seat warmer relay RH

H/L HI relay

Main relay No.2

H/L LOW relay

Seat warmer relay LH

Front fog light relay

Type B

Front blower relay

Rear blower relay

Fan relay

Cooling fan relay No.1

Cooling fan relay No.2

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Power Systems - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:41:28 AM

Page 8

«
...
2202
2203
2204
2205
2206
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды