Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 1901

Страница: 1901 / 2589

Fig. 58: Identifying Inner Garnish With Hook & Clips

Courtesy of MAZDA MOTORS CORP.

REAR DOOR TRIM DISASSEMBLY/ASSEMBLY

1. Disassemble in the order indicated in the table.
2. Assemble in the reverse order of disassembly.

Fig. 59: Identifying Rear Door Trim Components

Courtesy of MAZDA MOTORS CORP.

TRUNK END TRIM REMOVAL/INSTALLATION

1. Remove the trunk box. (See

TRUNK BOX REMOVAL/INSTALLATION

2. Remove the seat side box. (See

SEAT SIDE BOX REMOVAL/INSTALLATION

3. Detach clips A and pin B by pulling them in the direction of the arrow.
4. Remove the trunk end trim.
5. Install in the reverse order of removal.

2008 Mazda CX-9 Grand Touring

2008 BODY & ACCESSORIES Interior Trim - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:43:26 AM

Page 37

«
...
1899
1900
1901
1902
1903
...
»

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды