Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 543

Страница: 543 / 2589

Fig. 33: Identifying Rear Brake Components (Disc) & Torque Specifications

Courtesy of MAZDA MOTORS CORP.

DISC PLATE REMOVAL NOTE

1. If any disc plate is difficult to remove, perform the following steps to remove it.

1. Insert a flathead screwdriver into the service hole and turn the adjuster in the direction of the arrow

to compress the parking brake shoe.

2. Remove the disc plate.

2008 Mazda CX-9 Grand Touring

2008 BRAKES Conventional Brake System - Mazda CX-9

Microsoft

Sunday, November 15, 2009 9:48:49 AM

Page 28

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды