Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 454

Страница: 454 / 2589

Fig. 22: Identifying Rear Over Fender Lower And Rear Bumper Fascia With Nuts

Courtesy of MAZDA MOTORS CORP.

FRONT FENDER PANEL REMOVAL/INSTALLATION

1. Disconnect the negative battery cable.
2. Remove the following parts:

1. Windshield wiper arm and blade (See

WINDSHIELD WIPER ARM AND BLADE

REMOVAL/INSTALLATION

)

2. Side cowl grille (See

COWL GRILLE REMOVAL/INSTALLATION

)

3. Front over fender (See

OVER FENDER REMOVAL/INSTALLATION

)

4. Front bumper (See

FRONT BUMPER REMOVAL/INSTALLATION

)

5. Front combination lights (See

FRONT COMBINATION LIGHT

REMOVAL/INSTALLATION

)

6. Sail garnish (See

SAIL GARNISH REMOVAL/INSTALLATION

) '

3. Remove in the order indicated in the table.
4. Install in the reverse order of removal.

Fig. 23: Identifying Removing Sequence Of Front Fender Panel Components & Torque
Specifications

Courtesy of MAZDA MOTORS CORP.

2008 Mazda CX-9 Grand Touring

2008 ACCESSORIES & BODY, CAB Body Panels - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:44:45 AM

Page 15

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды