Mazda CX-9 Grand Touring 2008 Скачать руководство пользователя страница 418

Страница: 418 / 2589

Fig. 123: Identifying Squeeze Of Header Tabs Down

Courtesy of MAZDA MOTORS CORP.

5. Verify that the height of the header tabs is same as the height before removal.
6. Inspect for leakage from radiator. (See

ENGINE COOLANT LEAKAGE INSPECTION [MZI-3.7]

Fig. 124: Identifying Tab Height

Courtesy of MAZDA MOTORS CORP.

DRIVE PLATE REMOVAL/INSTALLATION [AW6A-EL, AW6AX-EL]

1. Remove the transaxle. (See

AUTOMATIC TRANSAXLE REMOVAL/INSTALLATION [AW6A-

EL, AW6AX-EL]

2. Remove in the order indicated in the figure.

2008 Mazda CX-9 Grand Touring

2008 TRANSMISSION Automatic Transaxle (AW6A-EL, AW6AX-EL) - Mazda CX-9

Microsoft

Sunday, November 15, 2009 10:29:31 AM

Page 90

Содержание CX-9 Grand Touring 2008






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды

Mazda CX-9 Grand Touring 2008, Руководство пользователя

Результаты поиска

Содержание CX-9 Grand Touring 2008

Отзывы:

Похожие инструкции для CX-9 Grand Touring 2008

Бренды по названию

Популярные бренды