background image

 

- 1 -               

650014B                                                

 

 

CRS-2000 & CRS-3000 

Cruise Control System 

Introduction 

You have purchased one of the finest Cruise Control Systems on the market. The Cruise Control features: 

         

Enhanced Adaptability 

 

 

Works with 3, 4, 5, 6 or 8 Cylinders  

 

Select ECM, AC Generator, Magnets, or 

         Pulse Sender as Speed Signal Source 

 

Quiet Operation Allows more Mounting Locations  

 

Select Acceleration Rate  

 

Selectable Gain Control  

 

Manual or Automatic Transmission Capability 

 

Compatible with Distributorless Ignition System 

Enhanced Features 

 

Modular Design

  

 

Removable Wiring Harness with Locking Device

  

 

Redesigned Water Sealing

  

 

Neutral Safety Switch (NSS) Compatible

  

 

Cruise Engaged Output (Ground Signal When 
Engaged)

  

 

Self Diagnostic

  

Easier Installation

 

 

No Vacuum Required

  

 

Smaller Module

  

 

Single Unit Mounting

  

 

Connectors with Positive Contact and Lock

  

 

No Clutch Switch Needed (except Diesel)

  

 

Additional Throttle Hardware Included in Kit

  

 

Compatible with Neutral Safety Connections 

Improved Operation 

 

Closer, More Accurate Control of Set Speed 

 

Accurate Coast/Reduce Speed  

 

Tap-Up, 1 MPH per tap  

 

Tap-Down, 1 MPH per tap  

 

Controlled Resume Rate  

 

 

 Here is an overview of the wiring diagram:   

 

Please Note:

 

If you are using L.E.D. taillights please wire in a relay as shown on page 3 to allow for 

proper Cruise Control operation. 
 
 
 

 

 
 
 
 

Содержание CRS-3000-3





















Отзывы: