manualshive.com logo in svg

NXP Semiconductors MPC5644A, Reference Manual, Page: 681 / 1735

Share
Download
NXP Semiconductors MPC5644A Reference Manual Download Page 681

Configurable Enhanced Modular IO Subsystem (eMIOS200)

MPC5644A Microcontroller Reference Manual, Rev. 6

Freescale Semiconductor

681

 

Figure 22-36. OPWMB mode with 0% duty cycle

Figure 22-37

 describes the operation of the OPWMB mode with the Output Disable signal being asserted. 

The Output Disable forces a transition in the output pin to the EDPOL bit value. After deasserted, the 
output disable allows the output pin to transition at the following A1 or B1 match. Note that the Output 
Disable does not modify the Flag bit behavior. Note that there is one system clock delay between the 
assertion of the output disable signal and the transition of the output pin to EDPOL.

1

4

match A1 negedge detection

8

A1 value

0x000004

A1 match

A1 match negedge detection

output pin 

EDPOL = 0

Selected

TIME

match B1 negedge detection

B1 match

B1 match negedge detection

B1 value

0x000008

clock

prescaler

A2 value

0x000000

 write to A2

0x000000

A1 match posedge detection

match A1 posedge detection

1

cycle n

cycle n+1

8

counter bus

FLAG set event

FLAG pin/register

Summary of Contents for MPC5644A








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments