manualshive.com logo in svg

NXP Semiconductors MPC5644A, Reference Manual, Page: 568 / 1735

Share
Download
NXP Semiconductors MPC5644A Reference Manual Download Page 568

Frequency-modulated phase locked loop (FMPLL)

MPC5644A Microcontroller Reference Manual, Rev. 6

568

Freescale Semiconductor

 

24

MODE

Mode of operation
This bit indicates whether the FMPLL is working in bypass mode or normal mode. The reset value 
indicates bypass mode. In legacy mode (FMPLL_ESYNCR1[EMODE] negated), the MODE bit will change 
to normal mode at the first time the FMPLL_SYNCR is written. In enhanced mode 
(FMPLL_ESYNCR1[EMODE] asserted), the MODE bit reflects the value of the CLKCFG[0] bit of the 
FMPLL_ESYNCR1.
0 Bypass mode
1 Normal mode

25

PLLSEL

Mode select
In previous MCUs of the MPC5500 family, this bit was used to differentiate between dual controller mode 
and normal mode (negated in bypass or dual controller mode, asserted in normal mode). Dual controller 
mode is not supported, therefore in legacy mode this bit resets to ‘0’ (bypass), but changes to ‘1’ (normal 
mode) at the first time the FMPLL_SYNCR is written. In enhanced mode, the MODE bit reflects the value 
of the CLKCFG[1] bit of the FMPLL_ESYNCR1.
0 Legacy mode: bypass or dual controller; enhanced mode: PLL off
1 Legacy mode: normal; enhanced mode: PLL on

26

PLLREF

FMPLL reference source
This bit indicates whether the FMPLL reference is from a crystal oscillator or from an external clock 
generator. The reset value is determined by the state of the PLLREF pin. In legacy mode, the reset value 
captured from the PLLREF pin cannot be changed anymore after reset. In enhanced mode, the PLLREF 
bit reflects the value of the CLKCFG[2] bit of the FMPLL_ESYNCR1.
0 External clock reference
1 Crystal oscillator reference

27

LOCKS

Sticky FMPLL lock status bit
This bit is set by the lock detect circuitry when the FMPLLL acquires lock after one of the following:
 • A system reset
 • A write to the FMPLL_SYNCR in legacy mode which changes the PREDIV or MFD fields
 • A write to the FMPLL_ESYNCR1 in enhanced mode which changes the EMODE, EPREDIV, EMFD or 

CLKCFG[1:2] fields

Whenever the FMPLL loses lock, LOCKS is cleared. LOCKS remains cleared even after the FMPLL 
relocks, until one of the three previously stated conditions occurs. Coming in bypass mode from system 
reset, LOCKS is asserted as soon as the FMPLL has locked, even if normal mode was not entered yet. If 
the FMPLL is locked, going from normal to bypass mode does not clear the LOCKS bit.
0 FMPLL has lost lock since last system reset or last write to PLL registers which affect the lock status. 
1 FMPLL has not lost lock.

28

LOCK

FMPLL lock status bit
Indicates whether the FMPLL has acquired lock. FMPLL lock occurs when the synthesized frequency 
matches to within approximately 4% of the programmed frequency. The FMPLL loses lock when a 
frequency deviation of greater than approximately 16% occurs. The flag is also immediately negated when 
the PREDIV or MFD fields of the SYNCR are changed in legacy mode, or when EMODE, EPREDIV, 
EMFD or CLKCFG[1:2] are changed in enhanced mode, and then asserted again when the PLL regains 
lock. If operating in bypass mode, the LOCK bit is still asserted or negated when the FMPLL acquires or 
loses lock.
0 FMPLL is unlocked. 
1 FMPLL is locked. 

Table 17-7. SYNSR field descriptions (continued)

Field

Description

Summary of Contents for MPC5644A








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments