manualshive.com logo in svg

NXP Semiconductors MPC5644A, Reference Manual, Page: 1467 / 1735

Share
Download
NXP Semiconductors MPC5644A Reference Manual Download Page 1467

FlexRay Communication Controller (FlexRay)

MPC5644A Microcontroller Reference Manual, Rev. 6

Freescale Semiconductor

1467

 

TBIF

Transmit Message Buffer Interrupt Flag

 — This flag is set if for at least one of the individual single 

or double transmit message buffers (FR_MBCCSRn[MTD] = 1) both the interrupt flag MBIF and the 
interrupt enable bit MBIE in the corresponding 

Message Buffer Configuration, Control, Status 

Registers (FR_MBCCSRn)

 are equal to 1. The application can not clear this TBIF flag directly. This 

flag is cleared by the CC when either all of the individual interrupt flags MBIF of the individual transmit 
message buffers are cleared by the application or the host has cleared the interrupt enables bit MBIE. 
0 None of the individual transmit message buffers has the MBIF and MBIE flag asserted.
1 At least one individual transmit message buffer has the MBIF and MBIE flag asserted.

MIE

Module Interrupt Enable

 — This flag controls if the Module Interrupt line is asserted when the MIF 

flag is set.
0 Disable interrupt line
1 Enable interrupt line

PRIE

Protocol Interrupt Enable

 — This flag controls if the Protocol Interrupt line is asserted when the PRIF 

flag is set.
0 Disable interrupt line
1 Enable interrupt line

CHIE

CHI Interrupt Enable

 — This flag controls if the CHI Interrupt line is asserted when the CHIF flag is 

set.
0 Disable interrupt line
1 Enable interrupt line

WUPIE

Wakeup Interrupt Enable

 — This flag controls if the Wakeup Interrupt line is asserted when the 

WUPIF flag is set.
0 Disable interrupt line
1 Enable interrupt line

FAFBIE

Receive FIFO Channel B Almost Full Interrupt Enable

 — This flag controls if the RX FIFO B Almost 

Full Interrupt line is asserted when the FAFBIF flag is set.
0 Disable interrupt line
1 Enable interrupt line

FAFAIE

Receive FIFO Channel A Almost Full Interrupt Enable

 — This flag controls if the RX FIFO A Almost 

Full Interrupt line is asserted when the FAFAIF flag is set.
0 Disable interrupt line
1 Enable interrupt line

RBIE

Receive Message Buffer Interrupt Enable

 — This flag controls if the Receive Message Buffer 

Interrupt line is asserted when the RBIF flag is set.
0 Disable interrupt line
1 Enable interrupt line

TBIE

Transmit Message Buffer Interrupt Enable

 — This flag controls if the Transmit Message Buffer 

Interrupt line is asserted when the TBIF flag is set.
0 Disable interrupt line
1 Enable interrupt line

Table 33-17. FR_GIFER field description (continued)

Field

Description

Summary of Contents for MPC5644A








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments