manualshive.com logo in svg

NXP Semiconductors MPC5644A, Reference Manual, Page: 347 / 1735

Share
Download
NXP Semiconductors MPC5644A Reference Manual Download Page 347

Interrupt Controller (INTC)

MPC5644A Microcontroller Reference Manual, Rev. 6

Freescale Semiconductor

347

 

15.2.4.2

Hardware vector mode

In hardware vector mode, the interrupt exception handler address is specific to the peripheral or software 
configurable interrupt source rather than being common to all of them. No IVOR is used. The interrupt 
exception handler address is calculated by hardware as shown in 

Figure 15-6

. The upper half of the 

interrupt vector prefix register (IVPR) is added to an offset, which corresponds to the peripheral or 
software interrupt source that caused the interrupt request. The offset matches the value in the Interrupt 
Vector field, INTC_IACKR[INTVEC]. Each interrupt exception handler address is aligned on a four-word 
(16-byte) boundary. IVOR4 is not used in this mode, and software does not need to read INTC_IACKR to 
get the interrupt vector number.

Figure 15-6. Hardware Vector Mode: Interrupt Exception Handler Address Calculation 

The processor negates INTC’s interrupt request when automatically acknowledging the interrupt request. 
However, the interrupt request to the processor do not negate if a higher priority interrupt request arrives. 
Even in this case, the interrupt vector number does not update to the higher priority request until the lower 
priority request is acknowledged by the processor.

The assertion of the interrupt acknowledge signal pushes the PRI value in the INTC_CPR onto the LIFO 
and updates PRI in the INTC_CPR with the new priority. 

15.3

External signal description

The INTC does not have any direct external MCU signals. However, there are 15 external pins that can be 
configured in the SIU as external interrupt request input pins. When configured for an external interrupt 
request function, an interrupt on that pin sets an external interrupt flag. These flags cause one of five 
peripheral interrupt requests to the interrupt controller. 

For more information on external interrupts, the pins used, and how to configure them:

•

Refer to the Signals chapter for a list and number of the external interrupt pins. 

•

Refer to the SIU chapter for more information on how to configure these pins.

15.4

Memory map and register definition

Table 15-2

 is the INTC memory map.

31

16

15

0

IVPR

31

28

27

16

15

0

0

+ Hardware vector 

15

0

0b0000

INTC_IACKR[INTVEC]

PREFIX

0x0000

PREFIX

18

0b000

19

0x0000

31

28

27

16

0b0000

IRQ SPECIFIC OFFSET

18

0b000

19

16

= Interrupt exception

handler address

mode offset

Summary of Contents for MPC5644A








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments