manualshive.com logo in svg

NXP Semiconductors MPC5644A, Reference Manual, Page: 589 / 1735

Share
Download
NXP Semiconductors MPC5644A Reference Manual Download Page 589

Error Correction Status Module (ECSM)

MPC5644A Microcontroller Reference Manual, Rev. 6

Freescale Semiconductor

589

 

non-correctable error is 

not

 reported by the master. Examples include speculative instruction fetches 

which are discarded due to a change-of-flow operation, and buffered operand writes. The ECC reporting 
logic in the ECSM provides an optional error interrupt mechanism to signal all non-correctable memory 
errors. In addition to the interrupt generation, the ECSM captures specific information (memory address, 
attributes and data, bus master number, etc.) which can be useful for subsequent failure analysis.

Register address: ECSM Base + 0x0043 (0xFFF4_0043)

0

1

2

3

4

5

6

7

R

0

0

ER1BR

EF1BR

0

0

ERNCR

EFNCR

W

Reset

0

0

0

0

0

0

0

0

= Unimplemented

Figure 18-4. ECC Configuration Register (ECSM_ECR)

Table 18-6. ECSM_ECR field description

Name

Description

2

ER1BR

Enable

 

RAM 1-bit Reporting

0 = Reporting of single-bit platform RAM corrections is disabled.
1 = Reporting of single-bit platform RAM corrections is enabled.

The occurrence of a single-bit RAM correction generates an ECSM ECC interrupt request as signalled 
by the assertion of ECSM_ESR[R1BC]. The address, attributes and data are also captured in the 
ECSM_REAR, ECSM_PRESR, ECSM_REMR, ECSM_REAT and ECSM_REDR registers.

3

EF1BR

Enable

 

Flash 1-bit Reporting

0 = Reporting of single-bit platform flash corrections is disabled.
1 = Reporting of single-bit platform flash corrections is enabled.

The occurrence of a single-bit flash correction generates an ECSM ECC interrupt request as signalled 
by the assertion of ECSM_ESR[F1BC]. The address, attributes and data are also captured in the 
ECSM_FEAR, ECSM_FEMR, ECSM_FEAT and ECSM_FEDR registers.

6

ERNCR

Enable

 

RAM Non-Correctable Reporting

0 = Reporting of non-correctable platform RAM errors is disabled.
1 = Reporting of non-correctable platform RAM errors is enabled.

The occurrence of a non-correctable multi-bit RAM error generates an ECSM ECC interrupt request as 
signalled by the assertion of ECSM_ESR[RNCE]. The faulting address, attributes and data are also 
captured in the ECSM_REAR, ECSM_PRESR, ECSM_REMR, ECSM_REAT and ECSM_REDR 
registers.

7

EFNCR

Enable

 

Flash Non-Correctable Reporting

0 = Reporting of non-correctable platform flash errors is disabled.
1 = Reporting of non-correctable platform flash errors is enabled.

The occurrence of a non-correctable multi-bit flash error generates an ECSM ECC interrupt request as 
signalled by the assertion of ECSM_ESR[FNCE]. The faulting address, attributes and data are also 
captured in the ECSM_FEAR, ECSM_FEMR, ECSM_FEAT and ECSM_FEDR registers.

Summary of Contents for MPC5644A








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments