manualshive.com logo in svg

NXP Semiconductors MPC5644A, Reference Manual, Page: 1412 / 1735

Share
Download
NXP Semiconductors MPC5644A Reference Manual Download Page 1412

FlexCAN Module

MPC5644A Microcontroller Reference Manual, Rev. 6

1412

Freescale Semiconductor

 

Figure 32-10. Rx Global Mask Register (RXGMASK)

32.4.5.5

Rx 14 Mask (RX14MASK)

This register is provided for legacy support and for low cost MCUs that do not have the individual masking 
per Message Buffer feature. For MCUs supporting individual masks per message buffer, setting 
MCR[MBFEN] causes the RX14MASK Register to have no effect on the module operation.

RX14MASK is used as acceptance mask for the Identifier in Message Buffer 14. When MCR[FEN] is set 
(FIFO enabled), the RXG14MASK also applies to element 6 of the ID filter table. This register has the 
same structure as the Rx Global Mask Register. It must be programmed while the module is in Freeze 
Mode, and must not be modified when the module is transmitting or receiving frames.

•

Address Offset: 0x14

•

Reset Value: 0xFFFF_FFFF 

32.4.5.6

Rx 15 Mask (RX15MASK)

This register is provided for legacy support and for low cost MCUs that do not have the individual masking 
per Message Buffer feature. For MCUs supporting individual masks per message buffer, setting 
MCR[MBFEN] causes the RX15MASK Register to have no effect on the module operation.

When MCR[MBFEN] is negated, RX15MASK is used as acceptance mask for the Identifier in Message 
Buffer 15. When MCR[FEN] is set (FIFO enabled), the RXG14MASK also applies to element 7 of the ID 
filter table. This register has the same structure as the Rx Global Mask Register. It must be programmed 
while the module is in Freeze Mode, and must not be modified when the module is transmitting or 
receiving frames.

Base + 0x0010

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

MI31 MI30 MI29 MI28 MI27 MI26 MI25 MI24 MI23 MI22 MI21 MI20 MI19 MI18 MI17 MI16

W

RESET:

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

MI15 MI14 MI13 MI12 MI11 MI10

MI9

MI8

MI7

MI6

MI5

MI4

MI3

MI2

MI1

MI0

W

RESET:

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

= Unimplemented or Reserved

Table 32-11. RXGMASK Register field descriptions

Field

Description

MI31–MI0

Mask Bits
For normal Rx message buffers, the mask bits affect the ID filter programmed on the message 
buffer. For the Rx FIFO, the mask bits affect all bits programmed in the filter table (ID, IDE, RTR).

1: The corresponding bit in the filter is checked against the one received
0: The corresponding bit in the filter is “don’t care”

Summary of Contents for MPC5644A








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments