Analog Devices ADSP-BF535 Blackfin Hardware Reference Manual Download | Manualshive

Page: 574 / 1022

background image

Device Mode Operation

13-12

ADSP-BF535 Blackfin Processor Hardware Reference

Inbound Error Detection and Reporting

Inbound transactions to ADSP-BF535 processor resources that are not
accessible to the PCI bus result in an error. Reads to non-accessible
resources result in the Error on Inbound Read bit being set in the

PCI_STAT

register and an interrupt to the processor core, if masked to do

so in the

PCI_ICTL

register. The waiting read on the PCI side is aborted.

Writes to non-accessible resources result in the Error on Inbound Write
bit being set in the

PCI_STAT

register and an interrupt to the core, if

masked to do so in the

PCI_ICTL

register. Writes are posted so that the

transaction may already be finished. However, if the transaction (for
example, a burst) is long enough, it is aborted by the error.

Supported Transactions From PCI

The PCI interface supports single 32-bit word memory and I/O accesses.
It also supports memory bursts of any number of 32-bit words. However,
the data FIFOs for inbound accesses are only 8 words deep, and if the
write data FIFO becomes full in the middle of a burst, the interface

retries

the PCI transaction. I/O bursts to the ADSP-BF535 processor are not
supported. The PCI interface also supports inbound fast back-to-back
transactions, a method of doing more than one single 32-bit word transfer
quickly, without the usual idle cycle between transfers. Inbound fast
back-to-back transfers are passed through as ordinary single word accesses.

Unsupported Transactions From PCI

PCI as a protocol is capable of addressing any combination of the 4 bytes
in a single word using its byte enable bits. This means that the
ADSP-BF535 processor could receive a transfer that it does not support,
such as a read or a write to bytes 0 and 2 of a word. On reads, this is not a
problem because the whole word can be read and the master of the trans-
action can take the data it wants.

«
...
572
573
574
575
576
...
»

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

SISPM1040-582-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 7

Brand: Yamaha Pages: 6

Brand: Yamaha Pages: 4

Brand: Yamaha Pages: 22

Brand: Yamaha Pages: 49

Brand: RadiSys Pages: 44

Brand: Lanner Pages: 109

Brand: Alesis Pages: 46

Urban Wireless CC-VT240W

Brand: Cateye Pages: 15

Brand: Waves Pages: 41

UniFi Cloud Key

Brand: Ubiquiti Pages: 13

Brand: QTech Pages: 406

PG-Flex FLC-704

Brand: PairGain Pages: 20

Brand: MA lighting Pages: 49

Brand: Softing Pages: 16

Brand: FiberHome Pages: 2

Tamar FCSAS102800

Brand: Bridgeworks Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands