manualshive.com logo in svg

Analog Devices ADSP-BF535 Blackfin, Hardware Reference Manual

The Analog Devices ADSP-BF535 Blackfin is a powerful digital signal processor. Enhance your understanding and utilization of this product by downloading the Hardware Reference Manual for free. Visit manualshive.com today to access the comprehensive manual and unlock the full potential of your Blackfin processor.

Share
Download
background image

Configuration Space Control and Status Registers

13-26

ADSP-BF535 Blackfin Processor Hardware Reference

 

Configuration Space Control and Status 
Registers

This section describes each of the MMRs for PCI that are accessible in the 
PCI Configuration Registers address space. All defined registers are writ-
able and readable. Reserved bits within a register read 0. Do not access 
reserved register name space. The address range for these registers is 
0xEEFF FF00 - 0xEEFF FFFF. Refer to 

“System MMR Assignments” on 

page B-1

 for the address of a particular register.

The configuration address space-based register space includes all PCI 
clock domain MMRs for the PCI peripheral. This includes the PCI device 
basic configuration registers consisting of sixty-four 32-bit words.

This register space also includes the memory space and I/O space BAR 
masks. These registers define the size of the respective memory areas made 
available to the PCI bus when the PCI peripheral functions as a PCI 
device. The corresponding BARs are part of the PCI configuration space 
and are programmed by the PCI bus host/bridge.

PCI Device Memory BAR Mask Register 

(PCI_DMBARM)

This register is a bit mask that specifies the size of the window available to 
a host processor on the PCI bus for access into the Blackfin processor’s 
memory space using memory space PCI transactions. The 

PCI_DMBARM

 reg-

ister is shown in 

Figure 13-9

. It is filled by the Blackfin processor core 

with 1s starting from the most significant bit (bit 31) down to the bit 
position corresponding to the window size available to the host processor. 
For example, if a 16 MB window is available for the host to use as a frame 
buffer in the Blackfin processor’s memory space, bits 31 through 24 would 
contain 1s and bits 0 through 23 would contain 0s. Bits 0 through 3 of 
this register are not writable and always contain 0s. As a result, the small-
est non zero window that can be specified is 16 bytes long. Similarly, bit 

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

D-Link Express EtherNetwork DFE-670TXD Quick Install Manual preview
Express EtherNetwork DFE-670TXD
Brand: D-Link Pages: 4
DAD DSX 26 User Manual preview
DSX 26
Brand: DAD Pages: 36
D-Link DUB-1320 Quick Install Manual preview
DUB-1320
Brand: D-Link Pages: 2
D-Link DXS-3610-54S Quick Installation Manual preview
DXS-3610-54S
Brand: D-Link Pages: 38
D-Link Web Smart DES-1210-28P Selection Manual preview
Web Smart DES-1210-28P
Brand: D-Link Pages: 6
D-Link xStack Storage DSN-4000 Series Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 23
D-Link Express EtherNetwork DI-604 Brochure preview
Express EtherNetwork DI-604
Brand: D-Link Pages: 7
D-Link xStack Storage DSN-4000 Series Cli User'S Manual preview
xStack Storage DSN-4000 Series
Brand: D-Link Pages: 97
dbx 902 Manual preview
902
Brand: dbx Pages: 8
Panasonic MICROCOMPUTER MN103S Connection Diagrams preview
MICROCOMPUTER MN103S
Brand: Panasonic Pages: 5
Panasonic MICROCOMPUTER MN103S Application Note preview
MICROCOMPUTER MN103S
Brand: Panasonic Pages: 21
Panasonic FP2 Series Manual preview
FP2 Series
Brand: Panasonic Pages: 56
Panasonic FP2 Series Product Manual preview
FP2 Series
Brand: Panasonic Pages: 28
Panasonic KX-HTS Series Quick Start Manual preview
KX-HTS Series
Brand: Panasonic Pages: 2
Panasonic WJMPU955 - PROCESSING UNIT - TMU Operating Instructions Manual preview
WJMPU955 - PROCESSING UNIT - TMU
Brand: Panasonic Pages: 62
Fostex DE-1 Service Manual preview
DE-1
Brand: Fostex Pages: 20
Blackmagicdesign Teranex 2D Processor Installation And Operation Manual preview
Teranex 2D Processor
Brand: Blackmagicdesign Pages: 969
Lanner NCA-1525 User Manual preview
NCA-1525
Brand: Lanner Pages: 78

Brands by name

Popular brands

Load more brands