Analog Devices ADSP-BF535 Blackfin Hardware Reference Manual Download | Manualshive

Page: 193 / 1022

background image

ADSP-BF535 Blackfin Processor Hardware Reference

4-47

Program Sequencer

To determine when to service an interrupt, the controller logically ANDs
the three quantities in

ILAT

,

IMASK

, and the current processor priority

level.

Servicing the highest priority interrupt involves these actions:

1. The interrupt vector in the EVT becomes the next fetch address.

On an interrupt, all instructions currently in the pipeline are
aborted. On a service exception, all instructions after the excepting
instruction are aborted. On an error exception, the excepting
instruction and all instructions after it are aborted.

2. The return address is saved in the appropriate return register.

The return register is

RETI

for interrupts,

RETX

for exceptions,

RETN

for NMIs, and

RETE

for debug emulation. The return address is the

address of the instruction after the last-executed instruction from
normal program flow.

3. Processor mode is set to the level of the event taken.

If the event is an NMI, exception, or interrupt, the processor mode
is Supervisor. If the event is an emulation exception, the processor
mode is Emulation.

4. Before the first instruction starts execution, the corresponding

interrupt bit in

ILAT

is cleared and the corresponding bit in

IPEND

is set.

Bit

IPEND[4]

is also set to disable all interrupts until the return

address in

RETI

is saved.

«
...
191
192
193
194
195
...
»

Summary of Contents for ADSP-BF535 Blackfin































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ADSP-BF535 Blackfin

Brand: Octavo Pages: 28

Brand: Obihai Pages: 2

ILDA Gem Laser projector tool

Brand: Stanwax Laser Pages: 3

StorageWorks AIT 35GB AutoLoader

Brand: Compaq Pages: 4

Super Sound Set SR-JV80-07

Brand: Roland Pages: 8

Brand: Schrack Technik Pages: 2

Brand: H3C Pages: 3

Brand: Kontron Pages: 42

Brand: LUX LUMEN Pages: 41

Brand: DFRobot Pages: 30

LatticeMico GPIO

Brand: Lattice Semiconductor Pages: 28

Brand: ETAS Pages: 36

Brand: Vista Pages: 93

Brand: Mitsubishi Pages: 188

Dummy IC M3T-SSOP36B-450

Brand: Renesas Pages: 4

Brand: NetApp Pages: 10

Brand: Aaeon Pages: 93

Brand: Aaeon Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands